Brand new pickup coil 200 ohms

Repair your stator

Often unavailable from the OEM manufacturer

All products shipped are tested

Two possible Pick-Up Pulsar Coils can fit on Polaris Sportsman 400 2004 and Sportsman 500 2004. The other possible part is RM00103. Please compare to your original part before buying.

Brand new pick up coil 200 ohms

• We offer a brand new pickup/pulser coil for you to repair your stator.
• Often unavailable from the OEM manufacturer
• All products shipped are tested

All item pictures are accurate; if in doubt do not hesitate to compare our item to your original part.

Suzuki Boulevard C90 VL1500 -- 2005-2009
Suzuki Boulevard C90T VL1500T -- 2005-2009
Suzuki Boulevard S40 LS650 -- 2005-2009, 2011-2019
Suzuki Boulevard S83 VS1400 GLP Intruder -- 2005-2009
Suzuki DR 650 S -- 1990-1993
Suzuki DR 650 SE -- 1994-2009, 2011-2019
Suzuki LS 650 Savage -- 1986-1988, 1995-2004
Suzuki VL 1500 Intruder -- 1998-2004
Suzuki VS 1400 GL Intruder -- 1987-2004

0802-037
0802-041
1UY-85510-20-00
1YW-85510-21-00
21V-85580-20-00
2NL-85580-20-00
2XK-85510-20-00
3089254
32101-09F00
32101-09F01
32101-09F20
32101-09F30
32101-09F40
32101-10F01
32101-12D00
32101-19A00
32101-24B00
32101-24B01
32101-24B02
32101-27H00
32101-27H10
32101-33H00
32101-38B00
32101-38B01
32101-38B02
32101-38F00
32101-45G00
32101-45G10
32150-19A10
3430-011
3430-045
3430-053
3430-058
3HN-85510-00-00
4011609
4BD-85510-00-00
4BD-85510-20-00
4BD-85580-00-00
4EX-85510-00-00
4JY-85510-00-00
59V-85510-20-00
59V-85580-20-00
32101-32E00
32150-09D10
32101-32E01
32150-19A00
32101-10F10
32101-10F11
4GY-81410-01-00
4GY-81410-02-00
4JH-81410-00-00
4TV-81410-00-00
4TV-81410-01-00
4VR-81410-00-00
0802-073
0802-065
32101-35K00
32101-09F02
32101-10F12
32101-33H01

Dimensions:
Height: 23 mm
Length: 20 mm
Width: 19 mm
Bracket center to center: 35 mm
Wires length : 700 mm

Other specifications:
Number of wires : 2
Number of terminals: 2

Wire to wire resistance:
Blue to Green = 200 ohms+/-20%

Not following these instructions may result in damaging the part or other components on your vehicle.

• By using a small soldering iron weld the wires to the ones on your OEM wiring harness.
• Insulate your solders with heat shrink.
• Before attempting to start your vehicle, adjusting the air gap is necessary for certain models.
• Rotate the flywheel by hand so the raised node is lined up with the pick up /pulsar coil and adjust as close as possible, but no less than 0.010??.
• If no spark or erratic spark, switch the wires at the plug.